Selca G13 Straight line, at a known angle, through a point or tangent to a circle
G13 X... Y... [I...] J... [K...]
| Parameter | Description |
|---|---|
| X,Y | Point or circle center coordinates. |
| I | Radius of the circle of tangency (omitted if it is a point). |
| J | Angle between straight line and X-axis. |
| K | Selects one of the intersections between the straight line and the circle programmed in the previous block. |
Selca G10 First point or circle that defines a straight line Programming G10 X… Y… [I…] Parameters Parameter Description X,Y Circle center or supporting point coordinates. I Circle radius (omitted…
Selca G11 Second point or Circle that defines a straight line Programming G11 X… Y… [I… K…] Parameters Parameter Description X,Y Circle center or supporting point coordinates. I Circle radius…
G70 Bolt Hole Circle G-Code (canned cycle) is very simple to program due to its small number of parameters. G70 bolt hole circle parameters are very self explanatory, but this…
Selca G20 Circle of known center and radius Programming G20 [X… Y…] [I…] [K…] Parameters Parameter Description X,Y Circle center coordinates. May be omitted if coinciding with the center of…
Selca G62 Type of coordinates for the definition of circle center in G2/G3 Programming G62 K… Parameters Parameter Description K type of coordinates. K1 absolute coordinates. K2 incremental coordinates, with…
Selca CNC 4000/3000 Series control G-Functions/ G-codes for cnc machinists who work on cnc machines with Selca cnc controls. These Selca G Functions work on following Selca cnc controls, Selca…
CNC G01 A… Angle Programming When using G1 (G01) G-code instructions as well as the end of movement co-ordinates X and/or Z, besides radii (G01 R…) or chamfers (G01 C…)…
0 BEGIN PGM 10107 MM 1 BLK FORM 0.1 Z X+0 Y+0 Z-40 2 BLK FORM 0.2 X+100 Y+100 Z+0 3 TOOL DEF 1 4 TOOL CALL 1 Z S1000…
NCT program example to show how to drill a part of a circle with G81 drilling cycle and G15 G16 Polar Coordinate Commands. G Codes G Code Function G15 polar…
Sinumerik HOLES2 Hole Circle With Sinumerik HOLES2 cycle, a hole circle can be machined (BHC). Programming HOLES2 (CPA, CPO, RAD, STA1, INDA, NUM) Parameters Parameter Description CPA Center point circle/pocket,…
Sinumerik SLOT1 Slots on a circle With Sinumerik SLOT1 cycle, slots can be produced arranged on a circle. The longitudinal axis of the slots has a radial orientation In contrast…
Sinumerik ANG= If the end points for the contour are not directly specified in the machining drawing, it is also possible to use an angle specification ANG=… to determine the…
Want to drill or tap in a circle, but you only know the radius of the circle and number of the holes. Then don’t worry G70 Bolt Hole Circle will…
G70 Bolt Hole Circle command makes it easy to drill/tap/bore in a circle at even distances. There is no need to know or calculate each hole position. You just are…
How to mill a full circle, no problem below is the cnc program example G-code which shows how to program a full circle on a cnc milling machine. Often cnc…
0 BEGIN PGM 10105 MM 1 BLK FORM 0.1 Z X-50 Y-50 Z-40 2 BLK FORM 0.2 X+50 Y+50 Z+0 3 TOOL DEF 1 4 TOOL CALL 1 Z S1000…
0 BEGIN PGM 10106 MM 1 BLK FORM 0.1 Z X+0 Y+0 Z-40 2 BLK FORM 0.2 X+100 Y+100 Z+0 3 TOOL DEF 1 4 TOOL CALL 1 Z S1000…
0 BEGIN PGM 10114 MM 1 BLK FORM 0.1 Z X-50 Y-50 Z-40 2 BLK FORM 0.2 X+50 Y+50 Z+0 3 TOOL DEF 1 4 TOOL CALL 1 Z S1000…
Sinumerik LONGHOLE Elongated holes on a circle With Sinumerik LONGHOLE cycle, elongated holes can be produced arranged on a circle. The width of the elongated hole is determined by the…
G72 Bolt Holes Along an Angle command makes it easy for a cnc machinists to Drill/Bore/Tap evenly spaced holes along an angle. G72 is non-modal G-code. G72 Bolt Holes Along…
