With Sinumerik HOLES2 cycle, a hole circle can be machined (BHC).
HOLES2 (CPA, CPO, RAD, STA1, INDA, NUM)
| Parameter | Description |
|---|---|
| CPA | Center point circle/pocket, abscissa (absolute) |
| CPO | Center point circle/pocket, ordinate (absolute) |
| RAD | Radius of circle (enter without sign) |
| STA1 | Starting angle Values: -180 to 180 degrees |
| INDA | Indexing angle |
| NUM | Number of holes/elongated holes/slots |
Want to drill or tap in a circle, but you only know the radius of the circle and number of the holes. Then don’t worry G70 Bolt Hole Circle will…
G70 Bolt Hole Circle command makes it easy to drill/tap/bore in a circle at even distances. There is no need to know or calculate each hole position. You just are…
G70 Bolt Hole Circle G-Code (canned cycle) is very simple to program due to its small number of parameters. G70 bolt hole circle parameters are very self explanatory, but this…
/*Parameters G65 P9100 Xx Yy Zz Rr Ff Ii Aa Bb Hh X: X coordinate of the center of the circle (#24) Y: Y coordinate of the center of the…
This CNC program example shows how both G72.1 and G72.2 figure copy functions can call one-another in one part program, read Programming Notes below carefully. Programming Fanuc G72.1 Rotational Copy Using G72.1…
Fadal L93NN Bolt Hole Circle (BHC) Fadal L93NN subroutine is used for pattern drilling in a circle usually called Bolt Hole Circle. Programming N5 L93NN R0… R1… R2… Parameters Parameter…
Following cnc sample program illustrates the use of G83 Peck Drilling Cycle with G70 Bolt Hole Circle G-code to machine evenly spaced deep drills in a circle. Although G70 Bolt…
Siemens Sinumerik CYCLE83 Peck drilling cycle makes deep hole drilling easy, Very flexible drilling cycle gives cnc machinists full control over all aspects of deep hole drilling tasks. CNC machinists…
A very simple cnc program example which shows the use of Siemens Sinumerik CYCLE83 Deep Hole Peck Drilling Cycle. Siemens Sinumerik CYCLE83 Deep Hole Peck Drilling Cycle Overview CYCLE83(RTP, RFP,…
Sinumerik SLOT1 Slots on a circle With Sinumerik SLOT1 cycle, slots can be produced arranged on a circle. The longitudinal axis of the slots has a radial orientation In contrast…
Sinumerik LONGHOLE Elongated holes on a circle With Sinumerik LONGHOLE cycle, elongated holes can be produced arranged on a circle. The width of the elongated hole is determined by the…
As with G70 Bolt Hole Circle a cnc machinists can machine drills/tap/bore evenly spaced holes in a circle, the same way sometimes you have to drill/tap/bore evenly spaced holes in…
CNC program example code for the G71 Bolt Hole Arc command. G71 bolt hole arc command makes it easy to drill/tap/bore evenly spaced holes in an arc. Canned cycles G73,…
Following cnc programming code shows the use of G72 bolt hole along an angle. As the names states G72 G-code makes it very easy to drill/bore/tap evenly spaced hole along…
G83 Peck Drilling Cycle G-code is modal so that it is activated every X and/or Y axis move, and it will rapid to that position and then cause this canned…
G83 Deep Hole Peck Drilling Canned Cycle Explanation G83 Peck Drilling Cycle G-code is modal so that it is activated every X and/or Y axis move, and it will rapid…
Okuma G73 High Speed Deep Hole Drilling Cycle G73 High Speed Deep Hole Drilling Cycle Programming G73 X__Y__Z__R__P__Q__F__ Parameters Parameter Description X,Y Coordinate values of hole position Z Hole bottom…
0 BEGIN PGM 10107 MM 1 BLK FORM 0.1 Z X+0 Y+0 Z-40 2 BLK FORM 0.2 X+100 Y+100 Z+0 3 TOOL DEF 1 4 TOOL CALL 1 Z S1000…
NCT program example to show how to drill a part of a circle with G81 drilling cycle and G15 G16 Polar Coordinate Commands. G Codes G Code Function G15 polar…
Selca G20 Circle of known center and radius Programming G20 [X… Y…] [I…] [K…] Parameters Parameter Description X,Y Circle center coordinates. May be omitted if coinciding with the center of…
