Haas Alarms

Alarm: 395 INVALID CODE IN CANNED CYCLE – Haas Lathe Haas Alarm Description: Any canned cycle requiring a PQ path sequence may not have an M code in the same…

Alarm: 394 B OVER TRAVEL RANGE – Haas Mill Haas Alarm Description: B-axis will exceed stored stroke limits. This is in a negative direction and is machine zero in the…

Alarm: 394 B OVER TRAVEL RANGE – Haas Lathe Haas Alarm Description: Tailstock (B-axis) will exceed stored stroke limits. This is in a negative direction and is machine zero in…

Alarm: 393 INVALID MOTION IN G74 OR G84 – Haas Mill Haas Alarm Description: Rigid Tapping G74 or G84 can only be in the Z minus direction. Make sure that…

Alarm: 393 INVALID MOTION IN G84 OR G184 – Haas Lathe Haas Alarm Description: Rigid Tapping can only be in the Z minus direction. Make sure that the distance from…

Alarm: 392 B AXIS DISABLED – Haas Mill Haas Alarm Description: Attempt made to program the B-axis while it was disabled (Disabled bit in Parameter 151 set to 1), invisible…

Alarm: 392 B AXIS DISABLED – Haas Lathe Haas Alarm Description: An attempt was made to program the B-axis while it was disabled (Disabled bit in Parameter 151 set to…

Alarm: 391 FEATURE DISABLED Haas Alarm Description: An attempt was made to use a software feature not enabled by a parameter bit. If the option was purchased and the parameter…

Alarm: 390 NO SPINDLE SPEED Haas Alarm Description: Required S code not commanded. Check program for a spindle speed command.

Alarm: 389 G17, G18, G19 ILLEGAL IN G68 Haas Alarm Description: Planes of rotation cannot be changed while rotation is enabled.Cancel rotation then select new plane.

Alarm: 388 CUTTER COMP NOT ALLOWED WITH G10 Haas Alarm Description: Coordinates cannot be altered while Cutter Comp is active. Move the G10 outside of Cutter Compensation enablement.

Alarm: 387 CUTTER COMP NOT ALLOWED WITH G103 Haas Alarm Description: If block lookahead has been limited, cutter compensation will not function. Remove the block limit for cutter compensation. Check…

Alarm: 386 INVALID ADDRESS FORMAT Haas Alarm Description: An alphabetical address was used improperly. Check your program.

Alarm: 385 INVALID L, P, OR R CODE IN G10 Haas Alarm Description: G10 was used to changes offsets but L, P, or R code is missing or invalid. Check…

Alarm: 384 METRIC IS NOT SELECTED Haas Alarm Description: G21 MM mode was specified but settings have selected inches. Change setting 9.

Alarm: 383 INCH IS NOT SELECTED Haas Alarm Description: G20 Inch mode was specified but settings have selected metric. Change setting 9.

Alarm: 382 D CODE REQUIRED IN G35 Haas Alarm Description: A Dnn code is required in G35 in order to store the measured tool diameter. Check your program.

Alarm: 381 G43,G44 NOT ALLOWED IN G36 OR G136 Haas Alarm Description: Auto work offset probing must be done without tool offset active. Check your program.

Alarm: 380 X, Y, A OR G49 NOT ALLOWED IN G37 Haas Alarm Description: G37 may only specify Z-axis and must have tool offset defined. Program the correct tool length…

Alarm: 379 SKIP SIGNAL NOT FOUND Haas Alarm Description: Skip signal check code included but skip not found when it was expected.

Alarm: 378 SKIP SIGNAL FOUND Haas Alarm Description: Skip signal check code included but skip was found when it was not expected.

Alarm: 377 NO SKIP IN GRAPH/SIM Haas Alarm Description: Graphics mode and program restart cannot simulate skip function. Use block delete in program blocks with skip functions for graphic simulation…

Alarm: 376 NO CUTTER COMP IN SKIP Haas Alarm Description: Skip G31 and G37 functions cannot be used with cutter compensation.Check your program and move the skip functions to another…

Alarm: 375 MISSING Z OR H IN G37 – Haas Mill Haas Alarm Description: G37 Automatic tool length measurement function requires H code, Z value, and tool offset enabled. X,…

Alarm: 374 MISSING XYZA IN G31 OR G36 – Haas Mill Haas Alarm Description: G31 skip function requires an axis motion.

Alarm: 374 MISSING XBZA IN G31 OR G36 – Haas Lathe Haas Alarm Description: G31 skip function requires an axis motion.

Alarm: 373 INVALID CODE IN DNC Haas Alarm Description: A code found in a DNC program could not be interpreted because of DNC restrictions. Check your program.

Alarm: 372 TOOL CHANGE IN CANNED CYCLE Haas Alarm Description: Tool change not allowed while canned cycle is active. Cancel canned cycles with G80 before advancing program to next tool.

Alarm: 371 INVALID I, J, K OR Q Haas Alarm Description: Check G150 cycle for missing or incorrect values for I, J, K or Q.

Alarm: 370 POCKET DEFINITION ERROR – Haas Mill Haas Alarm Description: Check geometry for G150. Check the sub program for path intersection and main program for starting X and Y….

Alarm: 370 TAILSTOCK EXCESSIVE DRIFT – Haas Lathe Haas Alarm Description: The tailstock position has changed even though it has not been commanded to do so. Check to make sure…

Alarm: 369 TOOL TOO BIG Haas Alarm Description: Tool too big to enter cut. Use a smaller tool.

Alarm: 368 GROOVE TOO SMALL Haas Alarm Description: Tool too big to enter cut. Use a smaller tool.

Alarm: 367 CUTTER COMP INTERFERENCE Haas Alarm Description: Programmed path cannot be computed with tool size. Use a different size tool or adjust the radius offset.

Alarm: 366 MISSING I, K, OR L IN G70, G71, G72 – Haas Mill Haas Alarm Description: Check canned cycles for missing values I, K or L.