Haas Alarms

Alarm: 451 BAR FEEDER SPINDLE INTERLOCK – Haas Lathe Haas Alarm Description: This means that discrete input 1027 (BF FLT) is high. See parameter 278 bit 21 CK BF SP…

Alarm: 450 BAR FEEDER FAULT – Haas Lathe Haas Alarm Description: This means that discrete input 1030 (BFSPLK) is high. See Parameter 278 bit 20 CK BF Status.

Alarm: 448 SERVO BAR OUT OF BARS – Haas Lathe Haas Alarm Description: Add more Bars.

Alarm: 447 SERVO BAR BAR IN WAY – Haas Lathe Haas Alarm Description: The end of bar switch was depressed and a load or unload bar was commanded. Remove the…

Alarm: 446 SERVO BAR BAR TOO LONG – Haas Lathe Haas Alarm Description: Bar that was just loaded is longer than Length of Longest Bar as displayed on Servobar current…

Alarm: 445 SERVO BAR FAULT – Haas Lathe Haas Alarm Description: Servobar program error.

Alarm: 444 REGEN ON TOO LONG – Haas Mill Haas Alarm Description: The power supply detected a condition in which the Regen stays active too long. This condition indicates that…

Alarm: 443 SERVO BAR ALREADY NESTED – Haas Lathe Haas Alarm Description: An Illegal G105 Pnnn was found in cutoff subprogram.

Alarm: 442 SERVO BAR MAX LENGTH REACHED – Haas Lathe Haas Alarm Description: Job Complete. Reset Current Length Run on Servobar current commands page.

Alarm: 441 SERVO BAR MAX BARS REACHED – Haas Lathe Haas Alarm Description: Job Complete. Reset Current # Bars Run on Servobar current commands page.

Alarm: 440 SERVO BAR MAX PARTS REACHED – Haas Lathe Haas Alarm Description: Job Complete. Reset Current # Parts Run on Servobar current commands page.

Alarm: 439 TAILSTOCK FOUND NO PART – Haas Lathe Haas Alarm Description: During an M21 or G01, the tailstock reached the hold point without encountering the part.

Alarm: 438 TAILSTOCK MOVED WHILE HOLDING PART – Haas Lathe Haas Alarm Description: The part moved while turning a part. Check Setting 107 and the actual position of the B…

Alarm: 437 TAILSTOCK UNDERSHOOT – Haas Lathe Haas Alarm Description: The tailstock did not reach its intended destination point. Check the value of parameter 293 or check Setting 107 compare…

Alarm: 436 DISK FILE NOT FOUND Haas Alarm Description: Could not find file by that name. File name needs to be entered as it is on floppy. Possible corrupted or…

Alarm: 435 DISK ABORT Haas Alarm Description: Could not read disk. Possible corrupted or unformatted disk, pressing reset during transmission. Try a known good disk or a new disk formatted…

Alarm: 434 FILE LOAD INSUFFICIENT MEMORY – Haas Mill Haas Alarm Description: Program loading into memory does not fit in available space.Check space available in the LIST PROG mode, download…

Alarm: 434 DISK LOAD INSUFFICIENT MEMORY – Haas Lathe Haas Alarm Description: Program received does not fit. Check the space available in the List Prog mode and possibly delete some…

Alarm: 433 FILE EMPTY PROG – Haas Mill Haas Alarm Description: Check your program. Between % and % there was no program found.

Alarm: 433 DISK EMPTY PROG – Haas Lathe Haas Alarm Description: Check your program. Between % and % there was no program found.

Alarm: 432 FILE ILLEGAL PROG NAME – Haas Mill Haas Alarm Description: Check files being loaded. Program must be Onnnnn and must be at the beginning of a block.

Alarm: 432 DISK ILLEGAL PROG NAME – Haas Lathe Haas Alarm Description: Check files being loaded. Program must be Onnnnn and must be at the beginning of a block.

Alarm: 431 DISK NO PROG NAME – Haas Lathe Haas Alarm Description: Need name in programs when receiving All; if not, no way to store them.

Alarm: 431 FILE NO PROG NAME – Haas Mill Haas Alarm Description: Program number missing in file when loading.

Alarm: 430 FILE UNEXPECTED END OF INPUT – Haas Mill Haas Alarm Description: Ending % sign not found. Check your program. An ASCII EOF code was found in the input…

Alarm: 430 FILE BEGINNING/END MARKER MISSING – Haas Lathe Haas Alarm Description: Beginning or ending % sign not found. Check program for start and end of file characters % format…

Alarm: 429 DISK DIR INSUFFICIENT MEMORY Haas Alarm Description: CNC memory full when attempt is made to read directory. Check space available in the LIST PROG and possibly delete or…

Alarm: 428 SERVO BAR SWITCH FAILURE – Haas Lathe Haas Alarm Description: One of the switches controlling the Servobar failed.

Alarm: 427 INTERRUPT OVERRUN Haas Alarm Description: The control detected an interrupt overrun condition. An interrupt occurred before the previous interrupt was completed. Call your dealer.

Alarm: 426 A SCALE/SCREW MISMATCH – Haas Mill Haas Alarm Description: Scale-induced correction exceeds one motor revolution.

Alarm: 426 SERVO BAR ILLEGAL CODE G105 – Haas Lathe Haas Alarm Description: Feed Bar commanded with an illegal code on block. Legal codes are I, J, K, P, Q,…

Alarm: 425 Z SCALE/SCREW MISMATCH – Haas Mill Haas Alarm Description: Scale-induced correction exceeds one motor revolution.

Alarm: 425 SERVO BAR LENGTH UNKNOWN – Haas Lathe Haas Alarm Description: Both the bar length and reference position are unknown.Unload the bar, Run G105 Q4 followed by G105 Q2…

Alarm: 424 Y SCALE/SCREW MISMATCH – Haas Mill Haas Alarm Description: Scale-induced correction exceeds one motor revolution.

Alarm: 424 SERVO BAR METRIC UNSUPPORTED – Haas Lathe Haas Alarm Description: Metric mode unsupported, change Setting 9 to inch.