Haas Alarms
Haas Alarms – Haas Alarm Codes with description.
Haas Alarm: 512 ILLEGAL ASSIGNMENT USE
Alarm: 512 ILLEGAL ASSIGNMENT USE Haas Alarm Description: Attempted to write to a read-only macro variable. See Operator manual macro section for valid variables. Parameter and setting variables are read…
Haas Alarm: 511 UNBALANCED RIGHT BRACKETS
Alarm: 511 UNBALANCED RIGHT BRACKETS Haas Alarm Description: Number of right brackets not equal to the number of left brackets.Check macro formatting.
Haas Alarm: 510 ILLEGAL OPERATOR OR FUNCTION USE
Alarm: 510 ILLEGAL OPERATOR OR FUNCTION USE Haas Alarm Description: See Operator manual macro section for valid variables.
Haas Alarm: 509 ILLEGAL MACRO VARIABLE USE
Alarm: 509 ILLEGAL MACRO VARIABLE USE Haas Alarm Description: See Operator manual macro section for valid variables.
Haas Alarm: 508 DIVISION BY ZERO
Alarm: 508 DIVISION BY ZERO Haas Alarm Description: A division in a macro expression attempted to divide by zero. Re-configure the macro expression. Check macro formatting for a calculation or…
Haas Alarm: 507 TOO FEW OPERANDS ON STACK
Alarm: 507 TOO FEW OPERANDS ON STACK Haas Alarm Description: An expression operand found too few operands on the expression stack. Cycle power on the machine. If the alarm reoccurs,…
Haas Alarm: 506 OPERAND STACK ERROR
Alarm: 506 OPERAND STACK ERROR Haas Alarm Description: The macro expression operand stack pointer is in error. Cycle power on the machine. If the alarm reoccurs, call your dealer and…
Haas Alarm: 505 VALUE STACK ERROR
Alarm: 505 VALUE STACK ERROR Haas Alarm Description: The macro expression value stack pointer is in error. Cycle power on the machine. If the alarm reoccurs, call your dealer and…
Haas Alarm: 504 UNBALANCED BRACKETS IN EXPRESSION
Alarm: 504 UNBALANCED BRACKETS IN EXPRESSION Haas Alarm Description: Unbalanced brackets, [ or ], were found in an expression. Add or delete a bracket. Check the macro formatting.
Haas Alarm: 503 ILLEGAL MACRO VARIABLE REFERENCE
Alarm: 503 ILLEGAL MACRO VARIABLE REFERENCE Haas Alarm Description: Macro variable programmed that is not supported by this control. Use the correct macro variable. Operator manual lists all system variables…
Haas Alarm: 502 [ OR = NOT FIRST TERM IN EXPRESSN
Alarm: 502 [ OR = NOT FIRST TERM IN EXPRESSN Haas Alarm Description: An expression element was found where it was not preceded by [or =, that start expressions. Check…
Haas Alarm: 501 TOO MANY ASSIGNMENTS IN ONE BLOCK
Alarm: 501 TOO MANY ASSIGNMENTS IN ONE BLOCK Haas Alarm Description: Only one assignment macro assignment is allowed per block. Divide assignment blocks into multiple blocks.
Haas Alarm: 487 USB DEVICE INAPPROPRIATELY UNMOUNTED
Alarm: 487 USB DEVICE INAPPROPRIATELY UNMOUNTED Haas Alarm Description: A USB device was removed during a critical operation. USB devices should not be disengaged during FNC or when the system…
Haas Alarm: 486 USB TIMEOUT OCCURRED
Alarm: 486 USB TIMEOUT OCCURRED Haas Alarm Description: The USB firmware experienced a timeout. This can occur if the USB media is extremely fragmented, or if there are many files…
Haas Alarm: 485 USB RESET OCCURRED
Alarm: 485 USB RESET OCCURRED Haas Alarm Description: The USB firmware experienced a reset. This can occur if the USB media is extremely fragmented, or if there are many files…
Haas Alarm: 474 G02 OR G03 NOT ALLOWED WITH G143 – Haas Mill
Alarm: 474 G02 OR G03 NOT ALLOWED WITH G143 – Haas Mill Haas Alarm Description: G02 and G03 allowed in G143 mode only if A and B axes are at…
Haas Alarm: 473 INVALID GEOMETRY – Haas Lathe
Alarm: 473 INVALID GEOMETRY – Haas Lathe Haas Alarm Description: The geometry specified by the G-code parameters is invalid. If using G76 or G92, either reduce Setting 95 (Thread Chamfer…
Haas Alarm: 472 ATM FAULT – Haas Mill
Alarm: 472 ATM FAULT – Haas Mill Haas Alarm Description: Indicates an error related to the Advanced Tool Management feature. ATM software encountered a group which does not exist. Usually…
Haas Alarm: 471 OUT OF TOOLS – Haas Mill
Alarm: 471 OUT OF TOOLS – Haas Mill Haas Alarm Description: The life of all tools in the programmed group have expired. Change tools and reset tool life data in…
Haas Alarm: 470 W LIMIT SWITCH – Haas Lathe
Alarm: 470 W LIMIT SWITCH – Haas Lathe Haas Alarm Description: Axis hit limit switch or switch disconnected. Stored stroke limits should stop slides before they hit limit switches. Verify…
Haas Alarm: 469 V LIMIT SWITCH – Haas Lathe
Alarm: 469 V LIMIT SWITCH – Haas Lathe Haas Alarm Description: Bar feeder hit limit switch or switch disconnected. Stored stroke limits should stop slides before they hit limit switches….
Haas Alarm: 468 U LIMIT SWITCH – Haas Lathe
Alarm: 468 U LIMIT SWITCH – Haas Lathe Haas Alarm Description: Axis hit limit switch or switch disconnected. Stored stroke limits should stop slides before they hit limit switches. Verify…
Haas Alarm: 464 W OVER TRAVEL RANGE – Haas Lathe
Alarm: 464 W OVER TRAVEL RANGE – Haas Lathe Haas Alarm Description: Commanded W-axis move would exceed allowed machine range.Coordinates are in the negative direction, and indicates an error in…
Haas Alarm: 463 V OVER TRAVEL RANGE – Haas Lathe
Alarm: 463 V OVER TRAVEL RANGE – Haas Lathe Haas Alarm Description: Commanded V-axis move would exceed allowed machine range.Coordinates are in the negative direction, and indicates an error in…
Haas Alarm: 462 U OVER TRAVEL RANGE – Haas Lathe
Alarm: 462 U OVER TRAVEL RANGE – Haas Lathe Haas Alarm Description: Commanded U-axis move would exceed allowed machine range.Coordinates are in the negative direction, and indicates an error in…
Haas Alarm: 461 APL GRIPPER TIMEOUT – Haas Lathe
Alarm: 461 APL GRIPPER TIMEOUT – Haas Lathe Haas Alarm Description: The gripper failed to reach its target position within the allowed time.
Haas Alarm: 460 APL ILLEGAL CODE – Haas Lathe
Alarm: 460 APL ILLEGAL CODE – Haas Lathe Haas Alarm Description: Internal software error; call your dealer.
Haas Alarm: 459 APL DOOR FAULT – Haas Lathe
Alarm: 459 APL DOOR FAULT – Haas Lathe Haas Alarm Description: Door was not completely open while APL was inside CNC, or Parameter 315 bit 5 was set to zero.
Haas Alarm: 458 LINEAR SCALES ENABLED WITHOUT MOTIF – Haas Mill
Alarm: 458 LINEAR SCALES ENABLED WITHOUT MOTIF – Haas Mill Haas Alarm Description: Linear scales is enabled on an axis but a MOTIF card was not detected.
Haas Alarm: 457 AUX AXIS IS ENABLED
Alarm: 457 AUX AXIS IS ENABLED Haas Alarm Description: One or more auxiliary axes are enabled. For the macro variables 750 and 751 to work the auxiliary axes must be…
Haas Alarm: 456 PARAMETER CONFLICT – Haas Lathe
Alarm: 456 PARAMETER CONFLICT – Haas Lathe Haas Alarm Description: Conflict between two or more of the Axis MOCON Channel parameters.
Haas Alarm: 455 G112 BLOCK ENDS W/O CANCEL CUTTER COMP – Haas Lathe
Alarm: 455 G112 BLOCK ENDS W/O CANCEL CUTTER COMP – Haas Lathe Haas Alarm Description: An X/Y cutter compensation exit move is required before a G113 is issued to cancel…
Haas Alarm: 454 C AXIS NOT ENGAGED – Haas Lathe
Alarm: 454 C AXIS NOT ENGAGED – Haas Lathe Haas Alarm Description: A command was given to the C-axis without the C-axis engaged. The C axis drive must be engaged…
Haas Alarm: 453 C AXIS ENGAGED – Haas Lathe
Alarm: 453 C AXIS ENGAGED – Haas Lathe Haas Alarm Description: A spindle command was given with the C-axis drive engaged. The C-axis motor must be disengaged with M155 before…
Haas Alarm: 452 SERVO BAR GEARMOTOR TIMEOUT – Haas Lathe
Alarm: 452 SERVO BAR GEARMOTOR TIMEOUT – Haas Lathe Haas Alarm Description: The motor which loads bars and the push rod did not complete its motion in the allowed time….