Centroid Alarms

Centroid Alarm 911 Illegal recursion Cause & Effect Attempt to execute a subprogram or macro that calls itself, either directly or indirectly. Job cancelled. Action Call correct subprogram.

Centroid Alarm 910 No subroutines in MDI Cause & Effect Specified O9100 – O9999 in MDI, which would begin an embedded subprogram. MDI cancelled.

Centroid Alarm 909 Program too long: job canceled Cause & Effect Attempt to run a job over 1MB in length, without the unlimited program size option. Job cancelled. Action Contact…

Centroid Alarm 907 _ axis travel exceeded on line NNNNN Cause & Effect Software travel limit would be exceeded by the requested move. Job cancelled. Action Check program, part zero…

Centroid Alarm 906 Warning: unknown arc on line NNNNN Cause & Effect Position of arc move could not be determined from parameters. Move is done as a linear move; job…

Centroid Alarm 905 Warning: 0 radius arc on line NNNNN Cause & Effect Arc move was specified with a zero radius. Move is done as a linear move; job continues….

Centroid Alarm 903 Warning: No coordinates for G50 on line NNNNN Cause & Effect G50 with no axis coordinates to set. Remainder of line processed; job continues. Action Add coordinates.

Centroid Alarm 902 No prior G28 or G30 on line NNNNN Cause & Effect G29 with no preceding G28 or G30. Action Add a G29 or G30.

Centroid Alarm 901 Ref. point invalid on line NNNNN Cause & Effect G30 with invalid P value (must be 1 or 2). Job cancelled. Action Change P-value to a 1…

Centroid Alarm 806 Error: No P value on line NNNNN Cause & Effect P value (dwell time) not specified for G82 or G89. Job cancelled. Action Add a P-value.

Centroid Alarm 805 Error: No Q value on line NNNNN Cause & Effect Q value not specified for G73 or G83. Job cancelled. Action Insert a Q-value.

Centroid Alarm 804 Error: Ggg invalid on line NNNNN (gg = 76, 86, 87, 88) Cause & Effect Unimplemented canned cycle requested. Job cancelled. Action Change to a valid Gcode.

Centroid Alarm 803 Error: No Z point on line NNNNN Cause & Effect No Z value specified for canned cycle. Job cancelled. Action Add a Z-value.

Centroid Alarm 802 Error: Q = 0 on line NNNNN Cause & Effect Q value of 0 specified (Q used for G73 and G83 only). Job cancelled. Action Insert a…

Centroid Alarm 801 Error: No R point on line NNNNN Cause & Effect No R-value specified. Job cancelled. Action Add an R-point.

Centroid Alarm 705 G10 error: No D, H, or P on line NNNNN Cause & Effect G10 used without D, H, or P to assign value. Job cancelled. Action Add…

Centroid Alarm 704 G10 error: invalid P on line NNNNN Cause & Effect G10 used with unknown P value. Job cancelled. Action Change P to a valid value.

Centroid Alarm 703 G10 error: invalid H on line NNNNN Cause & Effect G10 H0 Rxx specified. Job canceled (H0 cannot be set; it is always zero). Action Change H…

Centroid Alarm 702 G10 error: invalid D on line NNNNN Cause & Effect Job cancelled (D0 cannot be set; it is always zero). Action Change D to a valid value.

Centroid Alarm 701 G10 error: no R-value on line NNNNN Cause & Effect G10 used with no R-value. Job cancelled. Action Input an R-value.

Centroid Alarm 608 Ref. point move not allowed on line NNNNN Cause & Effect G28, G29, or G30 attempted during compensation. Job cancelled. Action Do not use return points with…

Centroid Alarm 607 Set home not allowed on line NNNNN Cause & Effect M26 attempted during compensation. Job cancelled. Action Do not use M26 with cutter comp.

Centroid Alarm 606 G53 not allowed on line NNNNN Cause & Effect G53 attempted during compensation. Job cancelled.

Centroid Alarm 605 Canned cycle not allowed on line NNNNN Cause & Effect Canned cycle attempted during compensation. Job cancelled. Action Do not use cutter comp. with canned cycles.

Centroid Alarm 603 Arc as first uncomp. move on line NNNNN Cause & Effect Arc specified as first move after end of compensation (G40). Job cancelled. Action First move after…

Centroid Alarm 601 Error: no compensation in MDI Cause & Effect G41 or G42 entered in MDI. MDI is not canceled, but cutter compensation does NOT go into effect. Remainder…

Centroid Alarm 549 Line too long Cause & Effect A line in a G/M-code program is too long (more than 1023 characters). Action Shorten the line.

Centroid Alarm 548 String too long Cause & Effect A quoted string was too long (usually a file name was longer than its allowed limit). Action Shorten the file name.

Centroid Alarm 547 Move by counts not allowed Cause & Effect Cutter comp (G41/G42) was on when M128 was specified Action Issue G40 (Cutter comp off) before issuing M128

Centroid Alarm 545 Value out of range Cause & Effect Parse error occurred because value was out of range Action Correct the value

Centroid Alarm 544 Too many axes Cause & Effect More than 1 axis was specified with M128, OR the Simultaneous Contouring feature is not enabled. Without the Simultaneous Contouring feature,…

Centroid Alarm 543 Missing L parameter Cause & Effect L code was missing Action Correct program.

Centroid Alarm 542 M22x character limit exceeded Cause & Effect The resultant formatted string after all the format codes were processed was too long. Action Correct program.

Centroid Alarm 540 M22x variable cannot be read Cause & Effect A format code was specified in the format string, but its corresponding #variable argument was invalid or there was…

Centroid Alarm 539 M22x variable type mismatch Cause & Effect A string format code was specified in the format string, but its corresponding #variable argument was numeric OR a numeric…