Fanuc Alarms

Fanuc Alarms and Errors e.g. Program errors (P/S alarm), Over travel alarms, Servo alarms etc.

Fanuc Alarm 1014 ILLEGAL FORMAT OF PROGRAM NO.

Fanuc Alarm 1014 ILLEGAL FORMAT OF PROGRAM NO. Fanuc Alarm Description Address O or N is not followed by a number.

Fanuc Alarm 1013 ILLEGAL POS. OF PROGRAM NO.

Fanuc Alarm 1013 ILLEGAL POS. OF PROGRAM NO. Fanuc Alarm Description Address O or N is specified where it must not (After the macro statement etc.).

Fanuc Alarm 1016 EOB NOT FOUND

Fanuc Alarm 1016 EOB NOT FOUND Fanuc Alarm Description EOB (End of Block) code is missing at the end of a program input in the MDI mode.

Fanuc Alarm 306 MISMATCH AXIS WITH CNR/CHF (T Series)

Fanuc Alarm 306 MISMATCH AXIS WITH CNR/CHF (T Series) Fanuc Alarm Description The correspondence between the moving axis and the I, J, or K command is incorrect in a block in…

Fanuc Alarm 304 G28 IS COMMANDED WITHOUT ZERO RETURN

Fanuc Alarm 304 G28 IS COMMANDED WITHOUT ZERO RETURN Fanuc Alarm Description Although a reference position was not set, an automatic return to the reference position (G28) was commanded.

Fanuc Alarm 305 INTERMEDIATE POSITION IS NOT ASSIGNED (M Series)

Fanuc Alarm 305 INTERMEDIATE POSITION IS NOT ASSIGNED (M Series) Fanuc Alarm Description Although a G28 (automatic return to the reference position) or G30 (return to the second, third, or fourth…

Fanuc Alarm 301 RESETTING OF REFERENCE RETURN IS INHIBITED

Fanuc Alarm 301 RESETTING OF REFERENCE RETURN IS INHIBITED Fanuc Alarm Description Although parameter No. 1012#0 (IDGx) was set to 1 to inhibit the reference position from being set again for…

Fanuc Alarm 302 SETTING THE REFERENCE POSITION WITHOUT DOG IS NOT PERFORMED

Fanuc Alarm 302 SETTING THE REFERENCE POSITION WITHOUT DOG IS NOT PERFORMED Fanuc Alarm Description The reference position could not be set for a return to the reference position without a…

Fanuc Alarm 300 ILLEGAL COMMAND IN SCALING

Fanuc Alarm 300 ILLEGAL COMMAND IN SCALING Fanuc Alarm Description An illegal G code was specified during scaling. Modify the program.

Fanuc Alarm 307 CAN NOT START REFERENCE RETURN WITH MECHANICAL STOPPER SETTING

Fanuc Alarm 307 CAN NOT START REFERENCE RETURN WITH MECHANICAL STOPPER SETTING Fanuc Alarm Description An attempt was made to set a butt-type reference position for an axis for which to…

Fanuc Alarm 310 FILE NOT FOUND

Fanuc Alarm 310 FILE NOT FOUND Fanuc Alarm Description The specified file could not be found during a subprogram or macro call.

Fanuc Alarm 311 CALLED BY FILE NAME FORMAT ERROR

Fanuc Alarm 311 CALLED BY FILE NAME FORMAT ERROR Fanuc Alarm Description An invalid format was specified to call a subprogram or macro using a file name.

Fanuc Alarm 312 ILLEGAL COMMAND IN DIRECT DRAWING DIMENSIONS PROGRAMMING (T Series)

Fanuc Alarm 312 ILLEGAL COMMAND IN DIRECT DRAWING DIMENSIONS PROGRAMMING (T Series) Fanuc Alarm Description Direct input of drawing dimensions was commanded in an invalid format. An attempt was made to…

Fanuc Alarm 317 ILLEGAL THREAD COMMAND IS IN THE THREAD CUTTING CYCLE (T Series)

Fanuc Alarm 317 ILLEGAL THREAD COMMAND IS IN THE THREAD CUTTING CYCLE (T Series) Fanuc Alarm Description A zero or a negative value is specified in a multiple repetitive canned threading…

Fanuc Alarm 313 ILLEGAL LEAD COMMAND (T Series)

Fanuc Alarm 313 ILLEGAL LEAD COMMAND (T Series) Fanuc Alarm Description The variable-lead threading increment specified in address K exceeds the specified maximum value in variable-lead threading. Or, a negative lead…

Fanuc Alarm 318 ILLEGAL RELIEF AMOUNT IS IN THE DRILLING CYCLE (T Series)

Fanuc Alarm 318 ILLEGAL RELIEF AMOUNT IS IN THE DRILLING CYCLE (T Series) Fanuc Alarm Description Although an escape directions is set in a multiple repetitive canned cutting-off cycle (G74 or…

Fanuc Alarm 314 ILLEGAL SETTING OF POLYGONAL AXIS (T Series)

Fanuc Alarm 314 ILLEGAL SETTING OF POLYGONAL AXIS (T Series) Fanuc Alarm Description An axis was specified invalidly in polygon turning. For polygon turning: 1) A tool rotation axis is not…

Fanuc Alarm 315 ILLEGAL NOSE ANGLE COMMAND IS IN THE THREAD CUTTING CYCLE (T Series)

Fanuc Alarm 315 ILLEGAL NOSE ANGLE COMMAND IS IN THE THREAD CUTTING CYCLE (T Series) Fanuc Alarm Description An invalid tool tip angle is specified in a multiple repetitive canned threading…

Fanuc Alarm 316 ILLEGAL CUTTING AMOUNT IS IN THE THREAD CUTTING CYCLE (T Series)

Fanuc Alarm 316 ILLEGAL CUTTING AMOUNT IS IN THE THREAD CUTTING CYCLE (T Series) Fanuc Alarm Description An minimum depth of cut higher than the thread height is specified in a…

Fanuc Alarm 319 THE END POINT COMMAND IS ILLEGAL IN THE DRILLING CYCLE (T Series)

Fanuc Alarm 319 THE END POINT COMMAND IS ILLEGAL IN THE DRILLING CYCLE (T Series) Fanuc Alarm Description Although the Δi or Δk travel distance is set to 0 in a…

Fanuc Alarm 320 ILLEGAL MOVEMENT AMOUNT/CUTTING AMOUNT IS IN THE DRILLING CYCLE (T Series)

Fanuc Alarm 320 ILLEGAL MOVEMENT AMOUNT/CUTTING AMOUNT IS IN THE DRILLING CYCLE (T Series) Fanuc Alarm Description A negative value is specified in a multiple repetitive canned cutting-off cycle (G74 or…

Fanuc Alarm 326 LAST BLOCK OF SHAPE PROGRAM IS A DIRECT DRAWING DIMENSIONS (T Series)

Fanuc Alarm 326 LAST BLOCK OF SHAPE PROGRAM IS A DIRECT DRAWING DIMENSIONS (T Series) Fanuc Alarm Description In a shape program in the multiple repetitive canned cycle (G70, G71, G72,…

Fanuc Alarm 328 ILLEGAL WORK POSITION IS IN THE TOOL NOSE RADIUS COMPENSATION (T Series)

Fanuc Alarm 328 ILLEGAL WORK POSITION IS IN THE TOOL NOSE RADIUS COMPENSATION (T Series) Fanuc Alarm Description The specification for the blank side for a tool nose radius compensation (G41…

Fanuc Alarm 330 ILLEGAL AXIS COMMAND IS IN THE TURNING CANNED CYCLE (T Series)

Fanuc Alarm 330 ILLEGAL AXIS COMMAND IS IN THE TURNING CANNED CYCLE (T Series) Fanuc Alarm Description An axis other than the plane is specified n a canned cycle(G90, G92, or…

Fanuc Alarm 334 OFFSET IS OUT OF EFFECTIVE RANGE

Fanuc Alarm 334 OFFSET IS OUT OF EFFECTIVE RANGE Fanuc Alarm Description An offset data which was out of the effective range was specified. (malfunction prevention function)

Fanuc Alarm 329 THE FINISHING SHAPE IS NOT A MONOTONOUS CHANGE(SECOND AXES) (T Series)

Fanuc Alarm 329 THE FINISHING SHAPE IS NOT A MONOTONOUS CHANGE(SECOND AXES) (T Series) Fanuc Alarm Description In a shape program for the multiple repetitive canned rough-cutting cycle (G71 or G72),…

Fanuc Alarm 325 UNAVAILABLE COMMAND IS IN SHAPE PROGRAM (T Series)

Fanuc Alarm 325 UNAVAILABLE COMMAND IS IN SHAPE PROGRAM (T Series) Fanuc Alarm Description An usable command was issued in a shape program for a multiple repetitive canned cycle (G70, G71,…

Fanuc Alarm 324 THE INTERRUPTION TYPE MACRO WAS DONE IN THE MULTIPLE REPETIVE CYCLES (T Series)

Fanuc Alarm 324 THE INTERRUPTION TYPE MACRO WAS DONE IN THE MULTIPLE REPETIVE CYCLES (T Series) Fanuc Alarm Description An interruption type macro was issued during the multiple repetitive canned cycle…

Fanuc Alarm 336 TOOL COMPENSATION COMMANDED MORE TWO AXES (M Series)

Fanuc Alarm 336 TOOL COMPENSATION COMMANDED MORE TWO AXES (M Series) Fanuc Alarm Description For a tool length compensation C, an attempt was made to command the offset to other axes…

Fanuc Alarm 323 THE FIRST BLOCK OF SHAPE PROGRAM IS A COMMAND OF TYPE II (T Series)

Fanuc Alarm 323 THE FIRST BLOCK OF SHAPE PROGRAM IS A COMMAND OF TYPE II (T Series) Fanuc Alarm Description Type II is specified in the first block of the shape…

Fanuc Alarm 322 FINISHING SHAPE WHICH OVER OF STARTING POINT (T Series)

Fanuc Alarm 322 FINISHING SHAPE WHICH OVER OF STARTING POINT (T Series) Fanuc Alarm Description An invalid shape which is over the cycle starting point is specified in a shape program…

Fanuc Alarm 321 ILLEGAL REPEATED TIME IS IN THE PATTERN REPEATING CYCLE (T Series)

Fanuc Alarm 321 ILLEGAL REPEATED TIME IS IN THE PATTERN REPEATING CYCLE (T Series) Fanuc Alarm Description A zero or a negative value is specified in a multiple repetitive canned closed…

Fanuc Alarm 327 MODAL THAT MULTIPLE REPETIVE CYCLES CANNOT BE DONE (T Series)

Fanuc Alarm 327 MODAL THAT MULTIPLE REPETIVE CYCLES CANNOT BE DONE (T Series) Fanuc Alarm Description A multiple repetitive canned cycle (G70, G71, G72, or G73) was commanded in a modal…

Fanuc Alarm 348 TOOL CHANGE Z AXIS POS NOT ESTABLISHED

Fanuc Alarm 348 TOOL CHANGE Z AXIS POS NOT ESTABLISHED Fanuc Alarm Description A tool change spindle on the Z-axis is not set.

Fanuc Alarm 347 TOOL CHANGE ILLEGAL COMMAND IN SAME BLK.

Fanuc Alarm 347 TOOL CHANGE ILLEGAL COMMAND IN SAME BLK. Fanuc Alarm Description Tool changing is commanded twice or more in the same block.

12345...