Fanuc Alarms

Fanuc Alarms and Errors e.g. Program errors (P/S alarm), Over travel alarms, Servo alarms etc.

Fanuc Alarm 1564 INDEX TABLE AXIS – OTHER AXIS SAME TIME (M Series)

Fanuc Alarm 1564 INDEX TABLE AXIS – OTHER AXIS SAME TIME (M Series) Fanuc Alarm Description The index table indexing axis and another axis have been specified in the same…

Fanuc Alarm 1567 INDEX TABLE AXIS DUPLICATE AXIS COMMAND (M Series)

Fanuc Alarm 1567 INDEX TABLE AXIS DUPLICATE AXIS COMMAND (M Series) Fanuc Alarm Description Index table indexing was specified during axis movement or on an axis for which the index…

Fanuc Alarm 1590 TH ERROR

Fanuc Alarm 1590 TH ERROR Fanuc Alarm Description A TH error was detected during reading from an input device. The read code that caused the TH error and how many…

Fanuc Alarm 1591 TV ERROR

Fanuc Alarm 1591 TV ERROR Fanuc Alarm Description An error was detected during the single–block TV error. The TV check can be suppressed by setting TVC parameter No. 0000#0 to…

Fanuc Alarm 1592 END OF RECORD

Fanuc Alarm 1592 END OF RECORD Fanuc Alarm Description The EOR (End of Record) code is specified in the middle of a block. This alarm is also generated when the…

Fanuc Alarm 1966 FILE NOT FOUND (MEMORY CARD)

Fanuc Alarm 1966 FILE NOT FOUND (MEMORY CARD) Fanuc Alarm Description The specified file could not be found on the memory card.

Fanuc Alarm 1967 FILE PROTECTED (MEMORY CARD)

Fanuc Alarm 1967 FILE PROTECTED (MEMORY CARD) Fanuc Alarm Description The memory card is write–protected.

Fanuc Alarm 1970 ILLEGAL CARD (MEMORY CARD)

Fanuc Alarm 1970 ILLEGAL CARD (MEMORY CARD) Fanuc Alarm Description This memory card cannot be handled.

Fanuc Alarm 1971 ERASE ERROR (MEMORY CARD)

Fanuc Alarm 1971 ERASE ERROR (MEMORY CARD) Fanuc Alarm Description An error occurred during memory card erase.

Fanuc Alarm 1972 BATTERY LOW (MEMORY CARD)

Fanuc Alarm 1972 BATTERY LOW (MEMORY CARD) Fanuc Alarm Description The memory card battery is low.

Fanuc Alarm 1973 FILE ALREADY EXIST

Fanuc Alarm 1973 FILE ALREADY EXIST Fanuc Alarm Description A file having the same name already exists on the memory card.

Fanuc Alarm 2032 EMBEDDED ETHERNET/DATA SERVER ERROR

Fanuc Alarm 2032 EMBEDDED ETHERNET/DATA SERVER ERROR Fanuc Alarm Description An error was returned in the built-in Ethernet/data server function. For details, see the error message screen of the built-in…

Fanuc Alarm 1964 NOT MOUNTED (MEMORY CARD)

Fanuc Alarm 1964 NOT MOUNTED (MEMORY CARD) Fanuc Alarm Description The memory card could not be mounted.

Fanuc Alarm 1965 DIRECTORY FULL (MEMORY CARD)

Fanuc Alarm 1965 DIRECTORY FULL (MEMORY CARD) Fanuc Alarm Description The file could not be generated in the root directory for the memory card.

Fanuc Alarm 1808 DEVICE DOUBLE OPENED

Fanuc Alarm 1808 DEVICE DOUBLE OPENED Fanuc Alarm Description An attempt was made to open a device that is being accessed.

Fanuc Alarm 1820 ILLEGAL DI SIGNAL STATE

Fanuc Alarm 1820 ILLEGAL DI SIGNAL STATE Fanuc Alarm Description 1) An each axis workpiece coordinate system preset signal was turned “1” in the state in which all axes on…

Fanuc Alarm 1969 ILLEGAL FORMAT (MEMORY CARD)

Fanuc Alarm 1969 ILLEGAL FORMAT (MEMORY CARD) Fanuc Alarm Description Check the file name.

Fanuc Alarm 1823 FRAMING ERROR(1)

Fanuc Alarm 1823 FRAMING ERROR(1) Fanuc Alarm Description The stop bit of the character received from the I/O device connected to reader/punch interface 1 was not detected.

Fanuc Alarm 1832 OVERRUN ERROR(2)

Fanuc Alarm 1832 OVERRUN ERROR(2) Fanuc Alarm Description The next character was received from the I/O device connected to reader/punch interface 2 before it could read a previously received character.

Fanuc Alarm 1961 NOT READY (MEMORY CARD)

Fanuc Alarm 1961 NOT READY (MEMORY CARD) Fanuc Alarm Description The memory card is not ready.

Fanuc Alarm 1962 CARD FULL (MEMORY CARD)

Fanuc Alarm 1962 CARD FULL (MEMORY CARD) Fanuc Alarm Description The memory card has run out of space.

Fanuc Alarm 1968 ILLEGAL FILE NAME (MEMORY CARD)

Fanuc Alarm 1968 ILLEGAL FILE NAME (MEMORY CARD) Fanuc Alarm Description Illegal memory card file name

Fanuc Alarm 1830 DR OFF(2)

Fanuc Alarm 1830 DR OFF(2) Fanuc Alarm Description The data set ready input signal DR of the I/O device connected to reader/punch interface 2 turned OFF.

Fanuc Alarm 1833 FRAMING ERROR(2)

Fanuc Alarm 1833 FRAMING ERROR(2) Fanuc Alarm Description The stop bit of the character received from the I/O device connected to reader/punch interface 2 was not detected.

Fanuc Alarm 1834 BUFFER OVERFLOW(2)

Fanuc Alarm 1834 BUFFER OVERFLOW(2) Fanuc Alarm Description The NC received more than 10 characters of data from the I/O device connected to reader/punch interface 2 even though the NC…

Fanuc Alarm 1912 V-DEVICE DRIVER ERROR (OPEN)

Fanuc Alarm 1912 V-DEVICE DRIVER ERROR (OPEN) Fanuc Alarm Description An error occurred during device driver control.

Fanuc Alarm 1960 ACCESS ERROR (MEMORY CARD)

Fanuc Alarm 1960 ACCESS ERROR (MEMORY CARD) Fanuc Alarm Description Illegal memory card accessing This alarm is also generated during reading when reading is executed up to the end of…

Fanuc Alarm 2054 THE NUMBER OF #40000 IS UNMATCH

Fanuc Alarm 2054 THE NUMBER OF #40000 IS UNMATCH Fanuc Alarm Description An attempt was made to enter an extended P-CODE-only variable not existing in the system.

Fanuc Alarm 1963 CARD PROTECTED (MEMORY CARD)

Fanuc Alarm 1963 CARD PROTECTED (MEMORY CARD) Fanuc Alarm Description The memory card is write–protected.

Fanuc Alarm 4010 ILLEGAL REAL VALUE OF OBUF :

Fanuc Alarm 4010 ILLEGAL REAL VALUE OF OBUF : Fanuc Alarm Description The real value for a output buffer is in error.

Fanuc Alarm 5009 PARAMETER ZERO (DRY RUN)

Fanuc Alarm 5009 PARAMETER ZERO (DRY RUN) Fanuc Alarm Description The dry run feedrate parameter No. 1410 or maximum cutting feedrate parameter No. 1430 for each axis has been set…

Fanuc Alarm 5305 ILLEGAL SPINDLE NUMBER

Fanuc Alarm 5305 ILLEGAL SPINDLE NUMBER Fanuc Alarm Description In a spindle select function by address P for a multiple spindle control, 1) Address P is not specified. 2) A…

Fanuc Alarm 5329 M98 AND NC COMMAND IN SAME BLOCK

Fanuc Alarm 5329 M98 AND NC COMMAND IN SAME BLOCK Fanuc Alarm Description A subprogram call which is not a single block was commanded during canned cycle mode.

Fanuc Alarm 5346 RETURN TO REFERENCE POINT

Fanuc Alarm 5346 RETURN TO REFERENCE POINT Fanuc Alarm Description The coordinate establishment of the Cs contour control axis is not made. Perform a manual reference position return. 1) When…

Fanuc Alarm 5362 CONVERT INCH/MM AT REF-POS

Fanuc Alarm 5362 CONVERT INCH/MM AT REF-POS Fanuc Alarm Description An inch/metric conversion was performed at a position other than the reference position. Perform an inch/metric conversion after returning to…