Fanuc Alarms

Fanuc Alarm SR873 FRAMING ERROR (RS422) Fanuc Alarm Description Fanuc 15 No stop bit was detected for a character received by the RS–422 interface.

Fanuc Alarm SR862 OVERRUN ERROR (MODEM CARD) Fanuc Alarm SR862 OVERRUN ERROR (ASR33/43) Fanuc Alarm Description Fanuc 15i Before a character received from the modem card could be read, the…

Fanuc Alarm SR863 FRAMING ERROR (MODEM CARD) Fanuc Alarm SR863 FRAMING ERROR (ASR33/ASR44) Fanuc Alarm Description Fanuc 15i The stop bit of a character received from the modem card was…

Fanuc Alarm SR864 BUFFER OVERFLOW (MODEM CARD) Fanuc Alarm SR864 BUFFER OVERFLOW (ASR33/ASR44) Fanuc Alarm Description Fanuc 15i Although the NC sent a stop code (DC3) to the modem card…

Fanuc Alarm SR870 DATA SET READY DOWN (RS422) Fanuc Alarm Description Fanuc 15 The data mode signal for the RS–422 interface went off.

Fanuc Alarm SR856 BUFFER OVERFLOW (RMT–BUF) Fanuc Alarm Description Fanuc 15i Reader/punch interface 10 received data exceeding a limit (512 characters with protocol B or 2560 characters with extended protocol…

Fanuc Alarm SR913 V–DEVICE DRIVER ERROR (COMMAND) Fanuc Alarm Description Fanuc 15i An error occurred during device driver control.

Fanuc Alarm SR860 DR OFF (MODEM CARD) Fanuc Alarm SR860 DATA SET READY DOWN (ASR33/43) Fanuc Alarm Description Fanuc 15i The data set ready input signal DR of the modem…

Fanuc Alarm SR861 CARRIER DETECT DOWN (ASR33/43) Fanuc Alarm Description Fanuc 10/11/12/15 The signal quality detection signal for the 20 mA current loop interface went off.

Fanuc Alarm SR914 V–DEVICE DRIVER ERROR (RANGE) Fanuc Alarm Description Fanuc 15i An error occurred during device driver control.

Fanuc Alarm SR915 V–DEVICE DRIVER ERROR (TEST) Fanuc Alarm Description Fanuc 15i An error occurred during device driver control.

Fanuc Alarm SR912 V–DEVICE DRIVER ERROR (OPEN) Fanuc Alarm Description Fanuc 15i An error occurred during device driver control.

Fanuc Alarm SR890 CHECK SUM ERROR (G05) Fanuc Alarm Description Fanuc 10/11/12/15/15i A checksum error occurred (in buffer transfer to remote buffer).

Fanuc Alarm SR891 ILLEGAL COMMAND G05 Fanuc Alarm Description Fanuc 15i G05 was specified in a state in which G05 cannot be specified.

Fanuc Alarm SR910 DEVICE DRIVER ERROR (UNDEFINED) Fanuc Alarm Description Fanuc 15i An error occurred during device driver control.

Fanuc Alarm SR911 V–DEVICE DRIVER ERROR (DEVICE) Fanuc Alarm Description Fanuc 15i An error occurred during device driver control.

Fanuc Alarm SR944 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i With protocol A, a time–out occurred (host error).

Fanuc Alarm SR945 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i With protocol A, the number of retries exceeded the limit (host error).

Fanuc Alarm SR946 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i A framing error or overrun error occurred.

Fanuc Alarm SR947 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i With protocol A, an invalid response command was received (host error).

Fanuc Alarm SR880 NOT DRAWING Fanuc Alarm Description Fanuc 10/11/12/15 Communication cannot be made with the graphic CPU.

Fanuc Alarm SR960 ACCESS ERROR (MEMORY CARD) Fanuc Alarm Description Fanuc 15i Illegal memory card accessing This alarm is also generated during reading when reading is executed up to the…

Fanuc Alarm SR961 NOT READY (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The memory card is not ready.

Fanuc Alarm SR940 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i Remote buffer software error

Fanuc Alarm SR941 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i The remote buffer board detected an invalid command (CNC error).

Fanuc Alarm SR949 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i The remote buffer is faulty. (Usually, the printed circuit board of the remote buffer is faulty.)

Fanuc Alarm SR950 DRIVER ERROR (MEMORY CARD) Fanuc Alarm Description Fanuc 15i An error occurred in the memory card device driver.

Fanuc Alarm SR962 CARD FULL (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The memory card has run out of space.

Fanuc Alarm SR971 ERASE ERROR (MEMORY CARD) Fanuc Alarm Description Fanuc 15i An error occurred during memory card erase.

Fanuc Alarm SR972 BATTERY LOW (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The memory card battery is low.

Fanuc Alarm SR948 COMMUNICATION ERROR (RMT_BUF) Fanuc Alarm Description Fanuc 15i With protocol A, a command error was detected (host error). The cause may be one of the following: 1….

Fanuc Alarm SR969 ILLEGAL FORMAT (MEMORY CARD) Fanuc Alarm Description Fanuc 15i Illegal memory card format

Fanuc Alarm SR970 ILLEGAL CARD (MEMORY CARD) Fanuc Alarm Description Fanuc 15i This memory card cannot be handled.

Fanuc Alarm SR1033 TIME OVER (DATA SERVER) Fanuc Alarm Description Fanuc 15i The CNC registered a time–out in the Ethernet/data server board function.

Fanuc Alarm SR1034 CNC ERROR (DATA SERVER) Fanuc Alarm Description Fanuc 15i An internal CNC error occurred by the Ethernet/data server board function.