Fanuc Alarms

Fanuc Alarm SR1033 TIME OVER (DATA SERVER) Fanuc Alarm Description Fanuc 15i The CNC registered a time–out in the Ethernet/data server board function.

Fanuc Alarm SR1034 CNC ERROR (DATA SERVER) Fanuc Alarm Description Fanuc 15i An internal CNC error occurred by the Ethernet/data server board function.

Fanuc Alarm SR965 DIRECTORY FULL (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The file could not be generated in the root directory for the memory card.

Fanuc Alarm SR966 FILE NOT FOUND (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The specified file could not be found on the memory card.

Fanuc Alarm SR1031 BUSY (DATA SERVER) Fanuc Alarm Description Fanuc 15i The board is busy in the Ethernet/data server board function.

Fanuc Alarm SR1032 BOARD ERROR (DATA SERVER) Fanuc Alarm Description Fanuc 15i An error was returned from the board in the Ethernet/data server board function.

Fanuc Alarm SR964 NOT MOUNTED (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The memory card could not be mounted.

Fanuc Alarm SR1030 NOT READY (DATA SERVER) Fanuc Alarm Description Fanuc 15i The board is not ready in the Ethernet/data server board function.

Fanuc Alarm SR963 CARD PROTECTED (MEMORY CARD) Fanuc Alarm Description Fanuc 15i The memory card is write–protected.

Fanuc Alarm SR973 FILE ALREADY EXIST Fanuc Alarm Description Fanuc 15i A file having the same name already exists on the memory card.

Fanuc Alarm SR1040 Device open error (Remote DGN.) Fanuc Alarm Description Fanuc 15i An error occurred in an attempt to open an I/O device for remote diagnosis.

Fanuc Alarm SV003 ABNORMAL CURRENT IN SERVO Fanuc Alarm Description Fanuc 10/11/12/15 Excessive current was detected in the velocity control circuit.

Fanuc Alarm SR1037 DOUBLE OPEN (DATA SERVER) Fanuc Alarm Description Fanuc 15i An attempt was made to open the file twice in the Ethernet/data server board function.

Fanuc Alarm SV004 EXCESS V TO MOTOR Fanuc Alarm Description Fanuc 10/11/12/15 Excessive voltage was detected in the velocity control circuit.

Fanuc Alarm SV005 EXCESS DISCHARGE I FROM MOTOR Fanuc Alarm Description Fanuc 10/11/12/15 Excessive discharge current from the motor was detected in the velocity control circuit.

Fanuc Alarm SR1036 MODE ERROR (DATA SERVER) Fanuc Alarm Description Fanuc 15i The mode could not be changed in the Ethernet/data server board function.

Fanuc Alarm SV002 BREAKER (FEED_CTL_UNIT) OFF Fanuc Alarm Description Fanuc 10/11/12/15 The breaker for the velocity control circuit tripped.

Fanuc Alarm SR1041 Illegal command (Remote DGN.) Fanuc Alarm Description Fanuc 15i An invalid command was specified for an I/O device for remote diagnosis.

Fanuc Alarm SR1042 Data input error (Remote DGN.) Fanuc Alarm Description Fanuc 15i An error occurred during data input to an I/O device for remote diagnosis.

Fanuc Alarm SR1043 Data output error (Remote DGN.) Fanuc Alarm Description Fanuc 15i An error occurred during data output from an I/O device for remote diagnosis.

Fanuc Alarm SW000 PARAMETER ENABLE SWITCH ON Fanuc Alarm Description Fanuc 10/11/12/15/15i The parameter setting is enabled (PWE, one bit of parameter No. 8000 is set to “1”). To set…

Fanuc Alarm SW010 BUBBLE FREE MODE AVAILABLE Fanuc Alarm Description Fanuc 10/11/12 Free mode switch of bubble memory was turned on.

Fanuc Alarm SV000 TACHOGENERATER DISCONNECT Fanuc Alarm Description Fanuc 10/11/12/15 The tachogenerator is disconnected.

Fanuc Alarm SV018 INCORRECT DSCG FREQUENCY Fanuc Alarm Description Fanuc 10/11/12/15 A fault was detected in a resolver or inductsyn feedback frequency check.

Fanuc Alarm SV001 EXCESS CURRENT IN SERVO Fanuc Alarm Description Fanuc 10/11/12/15 The servo motor was overloaded.

Fanuc Alarm SV019 INCORRECT PULSE CODER PULSE Fanuc Alarm Description Fanuc 10/11/12/15 A fault was detected in the feedback pulse from the pulse coder.

Fanuc Alarm SV020 INCORRECT PHASE SHIFT VALUE Fanuc Alarm Description Fanuc 10/11/12/15 The resolver or induction phase shift cannot be obtained correctly.

Fanuc Alarm SV021 1–REV PULSE SIGNAL INCORRECT Fanuc Alarm Description Fanuc 10/11/12/15 The single–revolution signal for the pulse coder went on at an incorrect position.

Fanuc Alarm SV006 VELOCTY UNIT POWER TOO LOW Fanuc Alarm Description Fanuc 10/11/12/15 Low voltage was detected in the velocity control circuit.

Fanuc Alarm SR1035 SEQUENCE ERROR (DATA SERVER) Fanuc Alarm Description Fanuc 15i A contradiction occurred in the CNC by the Ethernet/data server board function.

Fanuc Alarm SV008 EXCESS ERROR (STOP) Fanuc Alarm Description Fanuc 10/11/12/15/15i Position deviation during a stop is larger than the value set in parameter No. 1829. Check the value of…

Fanuc Alarm SV009 EXCESS ERROR (MOVING) Fanuc Alarm Description Fanuc 10/11/12/15/15i The position deviation during movement is larger than the value set in parameter No. 1828.

Fanuc Alarm SV010 EXCESS DRIFT COMPENSATION Fanuc Alarm Description Fanuc 10/11/12/15 Drift compensation is excessive (exceeded 500VELO).

Fanuc Alarm SV011 LSI OVERFLOW Fanuc Alarm Description Fanuc 15i The position deviation counter overflowed. Fanuc 10/11/12/15 The value specified for position deviation compensation is not within the range of…

Fanuc Alarm SV015 PULSE CODER DISCONNECTED Fanuc Alarm Description Fanuc 10/11/12/15 The pulse coder is disconnected.