Haas Settings

Haas Setting 63 Tool Probe Width Haas Setting Description This setting is used to specify the width of the probe used to test tool diameter. This setting only applies to…

Haas Setting 58 Cutter Compensation Haas Setting Description This setting selects the type of cutter compensation used (FANUC or YASNAC). See the cutter compensation section.

Haas Setting 57 Exact Stop Canned X-Y Haas Setting Description The rapid XY motion associated with a canned cycle may not achieve an exact stop when this setting is OFF….

Haas Setting 56 M30 Restore Default G Haas Setting Description When this setting is ON, ending a program with M30 or pressing Reset will return all modal G codes to…

Haas Setting 55 Enable DNC From MDI Haas Setting Description Turning this setting “ON” will make the DNC feature available. DNC is selected, in the control by pressing the MDI/DNC…

Haas Setting 54 Aux Axis Baud Rate Haas Setting Description This setting allows the operator to change the data rate for the second serial port (Auxiliary axis). This setting needs…

Haas Setting 53 Jog w/o Zero Return Haas Setting Description Turning this setting ON allows the axes to be jogged without zero returning the machine (finding machine home). This is…

Haas Setting 52 G83 Retract Above R Haas Setting Description (Range 0.0 to 30.00 inches or 0-761mm). This setting changes the way G83 (peck drilling cycle) behaves. Most programmers set…

Haas Setting 51 Door Hold Switch Override (Safety Switch Override) Haas Setting Description Selecting “OFF” will not allow a program to start when the doors are open, and opening a…

Haas Setting 50 Aux Axis Sync Haas Setting Description This changes the synchronization between sender and receiver for the second serial port. The second serial port is used for auxiliary…

Haas Setting 49 Skip Same Tool Change Haas Setting Description In some program, the same tool may be called in the next section of a program or a subroutine. The…

Haas Setting 44 Min F in Radius CC % Haas Setting Description (Minimum feedrate in radius cutter compensation percent) This setting affects the feedrate when cutter compensation moves the tool…

Haas Setting 43 Cutter Comp Type Haas Setting Description This setting controls how the first stroke of a compensated cut begins and the way the tool is cleared from the…

Haas Setting 42 M00 After M06 Haas Setting Description Turning this setting ON will stop the program after a tool change and a message will be displayed stating this. The…

Haas Setting 41 Add Spaces RS232 Out Haas Setting Description When this setting is ON spaces are added between address codes when a program is sent out via RS-232 serial…

Haas Setting 40 Tool Offset Measure Haas Setting Description This setting selects how tool size is specified for cutter compensation. It can be set to either Radius or Diameter.

Haas Setting 39 Beep at M00, M01, M02, M30 Haas Setting Description Turning this setting ON will cause the keyboard beeper to sound when an M00, M01 (with Optional Stop…

Haas Setting 38 Aux Axis Number Haas Setting Description This setting is used to select the number of external auxiliary axes added to the system. If it is set to…

Haas Setting 37 RS-232 Data Bits Haas Setting Description This setting is used to change the number of data bits for serial port 1 (RS-232). This setting must match the…

Haas Setting 36 Program Restart Haas Setting Description When this setting is ONN, restarting a program from a point other than the beginning will direct the control to scan the…

Haas Setting 35 G60 Offset Haas Setting Description This is a numeric entry in the range 0.0 to 0.9999 inches. It is used to specify the distance an axis will…

Haas Setting 34 4th Axis Diameter Haas Setting Description This is used to set the diameter of the A-axis (0.0 to 50 inches), which the control will use to determine…

Haas Setting 33 Coordinate System Haas Setting Description This setting changes the way the Haas control recognizes the work offset system when a G52 or G92 is programmed. It can…

Haas Setting 32 Coolant Override Haas Setting Description This setting controls how the coolant pump operates. The “Normal” selection allows the operator to turn the pump on and off manually…

Haas Setting 31 Reset Program Pointer Haas Setting Description When this setting is OFF, the Reset button will not change the position of the program pointer. When it is ON,…

Haas Setting 30 4th Axis Enable Haas Setting Description This setting initializes the control for a specific 4th axis. When this setting is OFF, the fourth axis is disabled; no…

Haas Setting 29 G91 Non-modal Haas Setting Description Turning this setting ON will use the G91 command only in the program block it is in (non-modal). When it is OFF,…

Haas Setting 28 Can Cycle Act w/o X/Z Haas Setting Description Turning this setting On will cause the commanded canned cycle to complete without an X or Z command. The preferred…

Haas Setting 28 Can Cycle Act w/o X/Y Haas Setting Description Turning this setting “ON” will cause the commanded canned cycle to complete without an X or Y command. The…

Haas Setting 27 G76/G77 Shift Dir. Haas Setting Description This setting controls the direction the tool is shifted (moved) to clear a boring tool during a G76 or G77 canned…

Haas Setting 26 Serial Number Haas Setting Description This is the serial number of your machine. It cannot be changed.

Haas Setting 25 EOB Pattern Haas Setting Description This setting controls the EOB (End of Block) pattern when data is sent and received to/from serial port 1 (RS-232). This setting…

Haas Setting 24 Leader To Punch Haas Setting Description This setting is used to control the leader (the blank tape at the beginning of a program) sent to a paper…

Haas Setting 23 9xxx Progs Edit Lock Haas Setting Description Turning this setting on will stop the 9000 series of programs from being viewed, edited or deleted. 9000 series programs…

Haas Setting 22 Can Cycle Delta Z Haas Setting Description This setting specifies the distance the Z-axis is retracted to clear chips during a G73 canned cycle. The range is…