Yasnac Alarms

Yasnac Alarm 50 PROG ERROR (G11/12) Yasnac Alarm Description I, K, R not correctly commanded for beveling and rounding. values of I, K, R, too large. Applies to Yasnac CNC Controls…

Yasnac Alarm 49 PROG ERROR (G41 – 44) Yasnac Alarm Description Reverse or almost reverse commanded in M97 mode. Applies to Yasnac CNC Controls LX1, LX2, LX3  

Yasnac Alarm 45 CAL ERROR (G41 – 44) Yasnac Alarm Description Intersection point not obtained by intersection computation. Applies to Yasnac CNC Controls LX1, LX2, LX3  

Yasnac Alarm 45 CAL ERROR (G41 – 44) Yasnac Alarm Description interference check error. Applies to Yasnac CNC Controls LX3

Yasnac Alarm 45 CAL ERROR (G41 – 44) Yasnac Alarm Description Circular arc designated circle radius R + 5 < tool radius D commanded in inside compensation of circular command. Applies…

Yasnac Alarm 44 TOOL DATA ERROR (R AND C) Yasnac Alarm Description Nose R is written in offset no. Specified by ?? of T**?? command. Applies to Yasnac CNC Controls LX3

Yasnac Alarm 43 PROG ERROR (M91) Yasnac Alarm Description P not specified in M91 block. Applies to Yasnac CNC Controls LX2  

Yasnac Alarm 35 PROG ERROR (T OFS) Yasnac Alarm Description Too large no. of T OFS code for tool position offset. LX3 Too large no. of T OFS code for tool…

Yasnac Alarm 30 PROG ERROR (F/E) Yasnac Alarm Description No F or E in feed command. E commanded in G98 mode. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 27 PROG ERROR (G41-44) Yasnac Alarm Description Error during nose radius compensation (error in circular interpolation mode). Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 26 PROG ERROR (G41-44) Yasnac Alarm Description Rise error in nose radius compensation. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 24 PROG ERROR (G, G41-44) Yasnac Alarm Description Unusable g code commanded during nose radius compensation. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 5 RESET UNREADY (AFTER EDITING) Yasnac Alarm Description cycle start without depressing reset button after editing. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 2 ZR UNREADY (Z) Yasnac Alarm Description Reference point return not completed z. LX3 Cycle started without returning reference point. Return to reference point. Applies to Yasnac CNC Controls LX1,…

Yasnac Alarm 1514 RESET UNREADY Yasnac Alarm Description After editing in edt mode, cycle start button is depressed in automatic operation mode without depression of reset key. Applies to Yasnac…

Yasnac Alarm 1215 G28 OR G29 PROGRAMMING ERROR Yasnac Alarm Description G29 is programmed without execution of G28 after power on. G28 or G29 is programmed in M95 (mirror image…

Yasnac Alarm 1115 AREA CHECK ERROR Yasnac Alarm Description Movement to the point out of prohibit area is commanded. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 1015 TAPE MEMORY CAPACITY ERROR Yasnac Alarm Description Operation data overflow the tape memory capacity caused by editing. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 915 M, S, OR T CODE DESIGNATION ERROR Yasnac Alarm Description M, S, T or B+ code is programmed in the block containing canned cycle command in effect….

Yasnac Alarm 815 AXIS OR R DESIGNATION ERROR Yasnac Alarm Description Axis of X, Y, Z or a is programmed in the block containing G12, G13, G14, G15 or G04….

Yasnac Alarm 715 COMPUTING ERROR Yasnac Alarm Description Calculation cannot be performed, caused by overflow or the like while intersection point is computed. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 615 TOOL RADIUS COMPENSATION C ERROR Yasnac Alarm Description Changing command of the plane for compensation. (G17 to G19) is made in G41 or G42 mode. G41 or…

Yasnac Alarm 515 CIRCULAR ARC PROGRAMMING ERROR (G02/G03) Yasnac Alarm Description I, J, K and R are mixedly commanded in programming circular arc. Radius value is zero or not specified…

Yasnac Alarm 514 TOOL OFFSET TAPE INPUT ERROR Yasnac Alarm Description Characters other than H, D and X are punched on the tape for tool offset value. Applies to Yasnac…

Yasnac Alarm 415 SUBPROGRAM ERROR Yasnac Alarm Description G25 is programmed in canned cycle mode. M98 or M99 is programmed in the block containing G25. Addresses P and Q are…

Yasnac Alarm 414 COMMANDING OF UNUSABLE CHARACTERS Yasnac Alarm Description Unusable characters or function characters are programmed. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 315 NO DATA FOR OPERATION Yasnac Alarm Description In mem operation mode, the program pointer comes into memory area where data for operation are not stored, caused by…

Yasnac Alarm 314 ADDRESS SEARCH ERROR Yasnac Alarm Description Address data to be searched by address search operation do not exist. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 215 ERRONEOUS PROGRAMMING OF G CODE Yasnac Alarm Description G43 or G44 is programmed in the modes other than G00, G01. G45, G46, G47 or G48 is programmed…

Yasnac Alarm 214 COMMANDING OF UNUSABLE G CODE Yasnac Alarm Description An unusable g code is programmed. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 115 F CODE UNSPECIFIED Yasnac Alarm Description After turning on power supply, movement other than positioning is commanded without specifying f command. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 114 BUFFER REGISTER OVERFLOW Yasnac Alarm Description More than 96 characters are programmed in a block. Applies to Yasnac CNC Controls 3000G

Yasnac Alarm 395 SERVO ALARM (5) Yasnac Alarm Description 5 axis servopack alarm 5. Applies to Yasnac CNC Controls MX3

Yasnac Alarm 385 AXIS ERROR (5) Yasnac Alarm Description Axis CPU error. Applies to Yasnac CNC Controls MX3

Yasnac Alarm 920 TAPE ERROR Yasnac Alarm Description Tape reading-in error (off-line)./ TAPE error. Applies to Yasnac CNC Controls MX1, MX2, MX3