Yasnac Alarms

Yasnac Alarm 117 MACRO ERROR (10) Yasnac Alarm Description MACRO ERROR (10) Applies to Yasnac CNC Controls J50M, MX3

Yasnac Alarm 135 EXT DATA Yasnac Alarm Description Error in data given by external data input. LX3 Error in data given by external data input. Need machine sequence’s or hardware’s check….

Yasnac Alarm 121 PRTN ERROR (G50/G92) Yasnac Alarm Description G31 commanded during program restart. This command prohibited. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 119 AS AFTER READ SUBPROG/MACRO Yasnac Alarm Description Address searched during execution of subprogram or macro program. This operation prohibited. Applies to Yasnac CNC Controls LX3

Yasnac Alarm 99 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Unusable addresses specified in G70 to G76 blocks. Address required in the block not specified. Check format and correct program. Applies to…

Yasnac Alarm 98 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Data specified by G70, P, Q not registered in internal keep memory. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 97 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Four or more processing interruptions by finished shape program in stock removal cycle by G71, or G72 R1. Applies to Yasnac CNC…

Yasnac Alarm 96 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description D (cutting frequency) specified by G73 zero or 128 or more. I, K (rough cutting) specified by G73 both zero. D, K…

Yasnac Alarm 95 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Faults in finished shape program specified by P, Q in G71, G72. LX3 Faults in finished shape program specified by P, Q…

Yasnac Alarm 90 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Beveling and rounding commands as last move command for finished shape program specified by P, Q, in G70, G71, G72 and G73….

Yasnac Alarm 93 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Unable G- and M- code in finished shape program specified by P, Q in G70, G71, G72, and G73 and correct program….

Yasnac Alarm 92 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description No. of blocks including finished shape program specified by P, Q in G70, G71, G72, and G73 , over 46. Applies to…

Yasnac Alarm 91 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description Block of sequence No. specified by P, Q, in G70 not found prog No. including in G70 block. Applies to Yasnac CNC…

Yasnac Alarm 90 PROG ERROR (G70-76/G72-78) Yasnac Alarm Description P, Q not commanded in G70, 71, 72, 73 block. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 80 TOOL SET CMP ERROR Yasnac Alarm Description T code commanded before G35 block. G98 commanded in or before G35 block. Applies to Yasnac CNC Controls LX1, LX2

Yasnac Alarm 89 PROG ERROR (G90/G92/G94) Yasnac Alarm Description Unusable addresses specified in G90, G92, and G94 blocks. R, B, C, P, Q, L not available. Applies to Yasnac CNC Controls…

Yasnac Alarm 87 PROG ERROR (G31/G35) Yasnac Alarm Description Touch switch not on when motion reaches end point by skip or tool set error compensation commands. LX3 Touch switch not on…

Yasnac Alarm 86 EXTERNAL CMP ERROR Yasnac Alarm Description Error input turned on during external tool compensation. Applies to Yasnac CNC Controls LX1, LX2

Yasnac Alarm 85 EXTERNAL CMP ERROR Yasnac Alarm Description Multiplication factor set by parameter exceeding 11 for external tool compensation. Applies to Yasnac CNC Controls LX1, LX2

Yasnac Alarm 84 TOOL WEAR CMP ERROR Yasnac Alarm Description Tool wear compensation inputs WOM, WOP given simultaneously. Applies to Yasnac CNC Controls LX1, LX2  

Yasnac Alarm 83 TOOL WEAR CMP ERROR Yasnac Alarm Description Compensation no. except 01 to 19 designated at tool wear compensation. Applies to Yasnac CNC Controls LX1, LX2  

Yasnac Alarm 82 TOOL SET CMP ERROR Yasnac Alarm Description Error of parameter setting for tool set error compensation (Z). Applies to Yasnac CNC Controls LX1, LX2

Yasnac Alarm 81 TOOL SET CMP ERROR Yasnac Alarm Description Error of parameter setting for tool set error compensation (x). Applies to Yasnac CNC Controls LX1, LX2  

Yasnac Alarm 72 PROG ERROR (G50T,G50XZ) Yasnac Alarm Description Set coordinate with t codes. g50t or g50xz commanded. Applies to Yasnac CNC Controls LX3  

Yasnac Alarm 67 POWER OFF WHILE EDITING Yasnac Alarm Description Power turned off during writing memory. Applies to Yasnac CNC Controls LX1  

Yasnac Alarm 66 CANNOT CONTINUOUS THREAD Yasnac Alarm Description Too short time for 1 block of continuous threadcutting. Change spindle speed command not to occur this error. Applies to Yasnac CNC…

Yasnac Alarm 64 PROG ERROR (G92/G78/G21) Yasnac Alarm Description Rapid thread pull-up value in Z-axis direction in thread cutting with beveling value set by parameter. Applies to Yasnac CNC Controls LX1,…

Yasnac Alarm 63 PROG ERROR (G92/G78/G21) Yasnac Alarm Description Rapid thread pull-up value in X-axis direction in thread cutting with beveling smaller than beveling value set by parameter. Applies to Yasnac…

Yasnac Alarm 62 PROG ERROR (G32/33) Yasnac Alarm Description Tread cutting commanded in G98 mode. LX3 Tread cutting commanded in G98 mode. Multi-Start thread cutting command B out of specified range…

Yasnac Alarm 61 PROG ERROR (G11/G12 IN THREAD) Yasnac Alarm Description Rounding, beveling command in thread cutting block. These commands prohibited. Applies to Yasnac CNC Controls LX1, LX2, LX3  

Yasnac Alarm 60 PROG ERROR (G34) Yasnac Alarm Description Lead increase / decrease value exceeding maximum programmable value during variable lead thread cutting. Minus value of lead commanded. Applies to Yasnac…

Yasnac Alarm 55 PROG ERROR (M, S, T) Yasnac Alarm Description M, S, T commands in the block in which M, S, T code cannot be commanded. LX3 M, S, T…

Yasnac Alarm 53 PROG ERROR (G50T/G92T) Yasnac Alarm Description Values of tool coordinate memory out of the range between 51 to 80 in work coordinate system setting by G50T. Applies to…

Yasnac Alarm 52 PROG ERROR (G01) Yasnac Alarm Description Angle programming not correct during angle programming linear interpolation by G01. Applies to Yasnac CNC Controls LX1, LX2, LX3

Yasnac Alarm 51 PROG ERROR (G11/12) Yasnac Alarm Description Tapering command in blocks for beveling and rounding. Applies to Yasnac CNC Controls LX1, LX2, LX3