Haas Settings

Haas Setting 107 TS Hold Point Haas Setting Description This setting is in absolute machine coordinates and should be a negative value. It is the point to advance to for…

Haas Setting 110 Warmup X Distance Haas Setting 112 Warmup Z Distance Haas Setting Description Settings 110 and 112 specify the amount of compensation (max = ± 0.0020″ or ± 0.051…

Haas Setting 103 CYC Start/FH Same Key Haas Setting Description The Cycle Start button must be pressed and held to run a program when this setting is ON. When Cycle…

Haas Setting 100 Screen Saver Delay Haas Setting Description When the setting is zero, the scren saver is disabled. If setting is set to some number of minutes, then after…

Haas Setting 99 Thread Minimum Cut Haas Setting Description Used in G76 canned threading cycle, this setting sets a minimum amount of successive passes of the thread cut. Succeeding passes…

Haas Setting 97 Tool Change Direction Haas Setting Description This setting determines the default tool change direction. It may be set to either Shortest or M17/M18. When “Shortest” is selected,…

Haas Setting 98 Spindle Jog RPM Haas Setting Description This setting determines the spindle rpm for the Spindle Jog key. The default value is 100 RPM.

Haas Setting 96 Thread Chamfer Angle Haas Setting Description See Setting 95. Valid range: 0 to 89 degrees (No decimal point allowed)

Haas Setting 91 Advanced Jog Haas Setting Description Turning this setting ON enables the Index Jog and Jog Travel Limits features. This setting is used on the Tool Room series…

Haas Setting 90 Max Tools To Display Haas Setting Description This setting limits the number of tools displayed on the Tool Geometry screen. The range of this setting is 1…

Haas Setting 88 Reset Resets Overrides Haas Setting Description This is an On/Off setting. When it is ON and the Reset key is pressed, any overrides are canceled and set…

Haas Setting 87 M06 Resets Override Haas Setting Description This is an On/Off setting. When this setting is ON and an M06 is commanded, any overrides are canceled and set…

Haas Setting 86 M39 Lockout Haas Setting Description This is an On/Off setting. When it is ON, M39 commands are ignored.

Haas Setting 85 Max Corner Rounding Haas Setting Description This setting defines the machining accuracy of rounded corners within a selected tolerance. The initial default value is 0.025 inch (except…

Haas Setting 84 Tool Overload Action Haas Setting Description This setting causes the specified action (Alarm, Feedhold, Beep, Autofeed) to occur anytime a tool becomes overloaded. (See the Tool Set…

Haas Setting 83 M30 Resets Override Haas Setting Description When this setting is ON, an M30 will restore any overrides (feedrate, spindle, rapid) to their default values (100%).

Haas Setting 82 Language Haas Setting Description Languages other than English are available in the Haas control. To change to another language, choose a language and press Enter.

Haas Setting 81 Tool At Power Up Haas Setting Description When the Power Up/Restart key is pressed, the control will change to the tool specified in this setting. If zero…

Haas Setting 80 Mirror Image B-axis Haas Setting Description This is an On/Off setting. When it is OFF, axis motions occur normally. When it is on, B axis motion may…

Haas Setting 79 5th-axis Diameter Haas Setting Description This is used to set the diameter of the B-axis (0.0 to 50 inches), which the control will use to determine the…

Haas Setting 78 5th axis Enable Haas Setting Description When this setting is OFF, the fifth axis is disabled and no commands can be sent to that axis. In order…

Haas Setting 77 Scale Integer F Haas Setting Description This setting allows the operator to select how the control interprets an F value (feedrate) that does not contain a decimal…

Haas Setting 76 Tool Release Lock Out Haas Setting Description When this setting is ON, the tool release key on the keyboard is disabled.

Haas Setting 75 9xxx PROGS Single BLK Haas Setting Description When Setting 75 is ON and the control is operating in Single Block mode, then the control will stop at…

Haas Setting 74 9xxxx PROGS Trace Haas Setting Description This setting, along with Setting 75, is useful for debugging CNC programs. When Setting 74 is ON, the control will display…

Haas Setting 73 G68 Incremental Angle Haas Setting Description This setting allows the G68 rotation angle to be changed for each commanded G68. When this switch is ON and a…

Haas Setting 72 Default G68 Rotation Haas Setting Description This specifies the rotation, in degrees, for a G68 command when the R address is not used. It must be in…

Haas Setting 71 Default G51 Scaling Haas Setting Description This specifies the scaling for a G51 (See G-Code Section, G51) command when the P address is not used. The default…

Haas Setting 70 DPRNT Open/Clos DCode Haas Setting Description This setting controls whether the POPEN and PCLOS statements in macros send DC control codes to the serial port. When the…

Haas Setting 69 DPRNT Leading Spaces Haas Setting Description This is an On/Off setting. When set to OFF the control will not use leading spaces generated by a macro DPRNT…

Haas Setting 68 Graphics Z Offset Haas Setting Description This setting locates the top of the zoom window relative to the machine Z zero position (see the Graphics section). Its…

Haas Setting 67 Graphics Y Offset Haas Setting Description This setting locates the top of the zoom window relative to the machine Y zero position (see the Graphics section). Its…

Haas Setting 66 Graphics X Offset Haas Setting Description This setting locates the right side of the scaling window relative to the machine X zero position (see the Graphics section)….

Haas Setting 65 Graph Scale (Height) Haas Setting Description This setting specifies the height of the work area that is displayed on the Graphics mode screen. The default value for…

Haas Setting 64 T. OFS Meas Uses Work Haas Setting Description This setting changes the way the Tool Ofset Mesur (Tool Offset Measure) button works. When this is ON, the…