Haas Settings

Haas Setting 142 Offset CHNG Tolerance Haas Setting Description This setting generates a warning message if an offset is changed by more than the amount entered for this setting. The…

Haas Setting 118 M99 Bumps M30 CNTRS Haas Setting Description When this setting is ON, an M99 will add one to the M30 counters (these are visible on the CURNT…

Haas Setting 143 Machine Data Collect Haas Setting Description This setting enables the user to extract data from the control using a Q command sent through the RS-232 port. See…

Haas Setting 119 Offset Lock Haas Setting Description Turning the setting ON will not allow the values in the Offset display to be altered. However, programs that alter offsets will…

Haas Setting 144 Feed Overide->Spindle Haas Setting Description This setting is intended to keep the chip load constant when an override is applied. When this setting is ON, any feedrate…

Haas Setting 120 Macro VAR Lock Haas Setting Description Turning this setting ON will not allow the macro variables to be altered. However, programs that alter macro variables will still…

Haas Setting 136 Server Haas Setting Description This setting contains the user-entered server name (up to 8 characters long.) Enter a semicolon (EOB symbol) if the machine is not linked…

Haas Setting 52 G83 Retract Above R Haas Setting Description Range 0.0 to 30.00 inches or 0-761mm). This setting changes the way G83 (peck drilling cycle) behave. Most programmers set…

Haas Setting 36 Program Restart Haas Setting Description When this setting is On, restarting a program from a point other than the beginning will direct the control to scan the…

Haas Setting 38 Aux Axis Number Haas Setting Description This is a numeric entry between 0 and 1. It is used to select the number of external auxiliary axes added…

Haas Setting 42 M00 After Tool Change Haas Setting Description Turning this setting On will stop the program after a tool change and a message will be displayed stating this.The…

Haas Setting 44 Min F in Radius TNC % Haas Setting Description (Minimum feedrate in radius tool nose compensation percent) This setting affects the feed rate when cutter compensation moves…

Haas Setting 72 Can Cycle Cut Depth Haas Setting Description Used with canned cycles G71 and G72, this setting specifies the incremental depth for each pass during rough cutting. It…

Haas Setting 56 M30 Restore Default G Haas Setting Description When this setting is On, ending a program with M30 or pressing Reset returns all modal G codes to their…

Haas Setting 57 Exact Stop Canned X-Z Haas Setting Description The rapid XZ motion associated with a canned cycle may not achieve an exact stop when this setting is Off….

Haas Setting 90 Graph Z Zero Location Haas Setting Description This setting adjusts for extreme values in tool geometry or shift values. In graphics, tool offsets are ignored so that…

Haas Setting 91 Graph X Zero Location Haas Setting Description This setting adjusts for extreme values in tool geometry or shift values. In graphics, tool offsets are ignored so that…

Haas Setting 92 Chuck Clamping Haas Setting Description This setting determines chuck clamping direction. Set to O.D., the chuck is considered clamped when the jaws are moved to the spindle…

Haas Setting 94 Tailstock Z Clearance Haas Setting Description This setting is the minimum allowable difference between the Z-axis and the tail stock (see Setting 93). Units are in inches….

Haas Setting 73 Can Cycle Retraction Haas Setting Description Used with canned cycles G71 and G72, this setting specifies the retraction amount after a roughing cut. It represents the tool…

Haas Setting 93 Tailstock X Clearance Haas Setting Description This setting works with Setting 94 to define a tail stock travel restriction zone that limits interaction between the tail stock…

Haas Setting 76 Foot Pedal Lock Out Haas Setting Description This is an On/Off setting. When it is Off, the foot pedal operates normally. When it is On, any action…

Haas Setting 81 Tool at Auto Off Haas Setting Description When the Power Up/Restart key is pressed, the control will change to the tool specified in this setting. If zero…

Haas Setting 86 Thread Finish Allowance Haas Setting Description Used in G76 canned threading cycle, this setting specifies how much material will be left on the thread for finishing after…

Haas Setting 87 TNN Resets Override Haas Setting Description This is an on/off setting. When M06 is executed and this setting is on, any overrides are canceled and set to…

Haas Setting 121 Foot Pedal TS Alarm Haas Setting Description When M21 is used to move the tail stock to the hold point and hold a part, the control will…

Haas Setting 122 SS Chuck Clamping Haas Setting Description This feature supports Subspindle lathes. Its value can be either O.D. or I.D; similar to Setting 92 for the main spindle.

Haas Setting 131 Auto Door Haas Setting Description This setting supports the Auto Door option. It should be set to On for machines with an autodoor. Also see M85/86 (Autodoor…

Haas Setting 132 Jog or Home Before TC Haas Setting Description When this setting is Off, the machine behaves normally. When it is On and Turret Fwd, Turret Rev, or…

Haas Setting 145 TS at Part for CS Haas Setting Description (Tail stock at part for Cycle Start) When it is Off, the machine behaves as before. When this setting…

Haas Setting 33 Coordinate System Haas Setting Description This setting changes the way tool shift offsets work. It can be set to either Yasnac or Fanuc. This setting changes the…

Haas Setting 102 C Axis Diameter Haas Setting Description This setting supports the C-axis. See the C-axis Section. The default value is 1.0 inches and the maximum allowable value is…

Haas Setting 105 TS Retract Distance Haas Setting Description The distance from the Hold Point (Setting 107) the tail stock will retract when commanded. This setting should be a positive…

Haas Setting 106 TS Advance Distance Haas Setting Description When the tail stock is moving toward the Hold Point (Setting 107), this is the point where it will stop its…

Haas Setting 107 TS Hold Point Haas Setting Description This setting is in absolute machine coordinates and should be a negative value. It is the point to advance to for…